Many people have done this project, and if not, you need to try it. It was easy and it’s useful.
Mine were both made from what I had around the house, left overs from other projects. The first one I did I used a wooden picture frame that had held a mirror (used on the wanted poster). It was from the dollar tree. I put cardboard inside the frame to back it since I had taken the mirror out.
First you want to find fabric, batting and ribbon. The fabric needs to be a few inches bigger than your frame on each side. The batting should be the same. I didn’t have batting, so I used stuffing. It came out a bit more lumpy, I like to think of it as cloud-like. The ribbon is tricky, measure your frame diagonally (I got 17 inches), add 2-3 inches (20). Multiply that by 4 (80).
Lay down your fabric and then your batting. Fold around the edges of your frame and staple them down. I used a staple gun, but a normal stapler can work also. Make sure you pull the fabric tight.
Next you will cut your ribbon. Of your total length, cut it in half. Then cut one of the halves into a quarter of the original length. Now you have a half piece, and two quarter pieces. Take one of the quarters and staple the edge onto the corner of the back of your frame.
Pull the ribbon across the front of the frame (over your fabric and batting) and staple the other side to the back of the frame. Make sure that the ribbon is laying flat. Do the same thing from the other two corners.
Next take the half piece of ribbon and staple it on the back between the two side corners. Pull the ribbon across the front of the frame to the middle of the top of the frame and staple it on the back. Fold the ribbon to go over the front of the frame and pull to the next side and staple it on the back. Fold it over, and pull it to the bottom middle of the frame. Staple and fold again. Pull it over back to the original side of the frame and staple it next to the other end of the ribbon. Confusing? The first picture is of the finished back of the first sample and the pictures below that are of my second sample. The thinner black ribbon is the first two quarters you stapled on, and the thicker brown ribbon is the single half-piece of ribbon.
That was all that I did on the first sample, I liked it just the way it was, I pinned on a cute flower and cute pin for whatever I wanted to hang on it later. The second sample I added a little more. I used pins to hold down the ribbons a bit tighter and for some cuter looks. On the backside after I pushed the pin though the cardboard I bent them and put a piece of duct tape to hold them down better. (If its on the back who cares what it looks like 🙂 I also stapled a loop of ribbon at the top to use when I went to hang it up. There are all sorts of variations you can do for this idea, just be creative and use what you have! You can find the first sample on etsy.com. Thanks for reading!
My dad was having a hard time throwing away his old magazines, so he felt better giving them to me. They were going out the next recycling day, but I decided to cut them up and make some word magnets from them. His magazines were all too ‘manly’ and it was hard trying to find words that weren’t “appliances”, “powerful”, or “software”.
First, gather all of your supplies. You will need magazines, magnets (those ones businesses give out to advertise and are stuck on your phone book), glass gems (mine were bought at the dollar tree craft section), scissors for paper, scissors for cutting the magnets, mod podge, and a paintbrush.
Next, you can start looking for words. Try to find a good selection of words, plenty of adjectives, verbs, nouns and pronouns. Think of how you would make sentences with these. Measure with an average sized gem to see how your word will look with it.
If you are using the free magnets from your phone book or from other businesses it helps to peel the advertisement part from the magnet. It usually leaves the white paper stuck to it, but that looks like a better background than the ad for your smaller words.
Once you find plenty of words its time to start getting messy. Dip your paintbrush in the mod podge and paint the flat side of the gem. Then stick the word onto the gem so that you only see the backside of the word. Paint over the word, and then stick the gem plus the word onto your magnet. Cut out around the magnet and then you can let your finished magnet dry.
It’s important to cover the whole back of the gem with the magnet or else it won’t be strong enough to stick to your fridge. Also, make sure that you don’t use too thick of paper, it can also make the magnet too heavy. If you don’t want to worry about it, buy some magnetic tape or magnets from the craft store.
Now you have a whole set of cute word magnets and you can leave fun (or funny!) messages on your fridge (or magnet board…. tutorial still to come!) Here’s my listing on etsy.com if you would rather me make these for you. Special orders are available. Thanks for reading!
This was a shirt that someone gave me, I loved the style of the shirt but it said something weird on it, in a font that made it only fit for kids in high school, and not my style.
First, I found some extra fabric I had laying around (actually a pair of white boxers that had been tossed into my scraps after my husband decided he didn’t like how they fit) and I cut a square out that covered the words.
The next step to making this fabric look cute is to make a stencil. I like to make my own stencils because then they’re personalized and because I don’t have to buy them. To make your own stencil, find an image (or if your artsy, draw one!) on a google image search or clip art. Then put it in word or paint and make it the size that you want it to be on your t-shirt and print it out on the card stock. Then you will cut it out. Keep in mind that sometimes if you don’t use a stencil image that there can be center pieces that will fall out (Think about cutting out an “A” and how you need the middle triangle to be there), so draw lines of parts you need to keep when you cut.
After you’ve made your stencil it’s time to paint it onto the fabric. Fabric paints work best, but I’ve found that acrylic paints still work, they wash fine and only fade a little. I sponged my star shape on and then brushed the silver on around it. I also stitched on a button in the center.
When your fabric is finished it’s time to take it to the sewing machine. I used a zig-zag stitch to keep the frayed ends from fraying too much and sewed a big square around the writing on the shirt.
Hope you can use this idea to make something even cuter!
We saw this idea at a trading post near the Grand Canyon and it was a super cute idea. I may be a little biased but I think mine looks much better, it’s a little less trading-posty/cheesy. I made it for our cowboy themed spare bedroom, but since then it has turned into a nursery.
Cardstock (or stencils)
1. If the plywood isn’t cut to the size you want, have it cut at the store or cut it at home. I had my husband do it, he’s the best!
2. Use a few browns to paint it like wood. I had a few helpers and we all just swiped brown up and down in random places until it was covered.
3. Make stencils for the words using cardstock or thin cardboard (think: cereal box). Make sure that you don’t cut out the negative spaces. If you don’t want to make stencils, they can be found in home improvement stores and craft stores.
4. Using a sponge brush or a stenciling brush and dab paint onto the stencils. For more on stenciling check out this post here on how I stenciled charger plates.
5. After all the paint is dry, glue your mirror onto the plywood using tacky glue or some sort of super glue.
6. Using hot glue, put the leather cord around the edges of the mirror.
7. Finally, add a frame back and hang on the wall.
That’s all folks! I loved mine, but we decided against having a cowboy room in the house once we did the nursery so my sign was sold for way too little at a yard sale. Hopefully it is well loved and that the one you make will be well loved too!
I created this wall hanging for our apartment to make it look a little more homey. The frame itself was a bit hideous in the beginning, but I had found it at Goodwill for a decent price.
First, I mod poodged scrapbook paper to the frame.
Next I painted the extra cardboard in the frame black.
The gray and flowers paper you see is just plain white cardstock that I laid out and painted by hand. In the swirls are me and my husband’s names. After painting all the flowers, leaves and swirls I used a silver paint and a stiff bristly brush to lightly texture over everything. These papers were then glued to the cardboard backing.
Next the ribbon was glued to the backing, and the bow tied afterwards.
I made my own stencils from cardstock so that they would last longer than one use. I still have them in a folder. I stenciled “Love” onto the same scrapbook paper used for the frame, and backed them with brown paper. These were then glued on.
The cardboard was then put into the frame, carefully so that the bow would look good and not crushed funny. It was the only thing that hung on the wall in our first apartment, and still hangs on the wall in our home.